超聲波清洗機既有清洗功能，又有乳化、加速溶解、分散等多種功能。在很多行業都有著廣泛的應用，那么在使用過程中一旦出現問題就應該解決嗎？
The ultrasonic cleaning machine not only has the cleaning function, but also has the functions of emulsification, accelerated dissolution, dispersion, etc. It is widely used in many industries. Should problems be solved once they occur in the use process?
1、保險損壞如果超聲波清洗機的保險損壞，首先檢查電源插座中的保險是否燒毀。拿出安全表，用萬用表檢查一下。如果損壞，請立即更換。
1. Insurance damage If the insurance of the ultrasonic cleaner is damaged, first check whether the fuse in the power socket is burnt out. You'd better take out the safety watch and check it with a multimeter. If it is damaged, replace it immediately.
2、傳感器損壞由于長期高溫使用，陶瓷部分損壞。在這種情況下，應使用儀器測量傳感器的絕緣強度。在很多情況下，傳感器內部陶瓷會損壞，影響工作。
2. Sensor damage The ceramic part is damaged due to long-term high temperature use. In this case, an instrument should be used to measure the insulation strength of the sensor. In many cases, the ceramic inside the sensor will be damaged, affecting the work.
3、隔離變壓器損壞如果長期使用超聲波清洗機，電感器和變壓器是電子元件，可能導致短路。大部分損壞的電感變壓器都會燒焦，因此應立即更換新零件。

3. The isolation transformer is damaged If the ultrasonic cleaner is used for a long time, the inductor and transformer are electronic components, which may cause short circuit. Most of the damaged inductive transformers will be burnt, so new parts should be replaced immediately.
超聲波清洗機在使用過程中還可能遇到調節管損壞、動力管損壞等情況，針對以上不同的故障情況，可以處理或找維修人員解決。
The ultrasonic cleaning machine may also encounter damage to the regulating pipe and power pipe during use. For the above different faults, you can handle them or find professional maintenance personnel to solve them.
超聲波清洗機維修保養問題
Maintenance problems of ultrasonic cleaning machine
清洗機由超聲波發生器和超聲波換能器組成，超聲波換能器是由壓電陶瓷材料制造的夾芯式換能器，壓電陶瓷材料在交變電場的作用下會產生機械振動。
The cleaning machine is composed of an ultrasonic generator and an ultrasonic transducer. The ultrasonic transducer is a sandwich transducer made of piezoelectric ceramic materials, which will generate mechanical vibration under the action of an alternating electric field.
超聲波換能器常見問題
Common problems of ultrasonic transducer
1 超聲波振子受潮，可以用兆歐表檢查與換能器相連接的插頭，檢查絕緣電阻值就可以判斷基本情況，一般要求絕緣電阻大于5兆歐以上。如果達不到這個絕緣電阻值，一般是換能器受潮，可以把換能器整體（不包括噴塑外殼）放進烘箱設定100℃左右烘干3小時或者使用電吹風去潮至阻值正常為止。
1 If the ultrasonic vibrator is affected with moisture, the plug connected to the transducer can be checked with a megger. The basic situation can be judged by checking the insulation resistance value. Generally, the insulation resistance is required to be greater than 5 megohms. If the insulation resistance value cannot be reached, the transducer is generally affected with moisture, so the whole transducer (excluding the plastic sprayed shell) can be put into the oven and set at about 100 ℃ for drying for 3 hours, or use a hair dryer to remove moisture until the resistance value is normal.
2 換能器振子打火，陶瓷材料碎裂，可以用肉眼和兆歐表結合檢查，一般作為應急處理的措施，可以把個別損壞的振子斷開，不會影響到別的振子正常使用。
2 If the transducer vibrator is ignited and the ceramic material is broken, it can be checked with naked eyes and a megger. Generally, as an emergency treatment measure, individual damaged vibrators can be disconnected without affecting the normal use of other vibrators.
3 振子脫膠，我們的換能器是采用膠結，螺釘緊固雙重保證工藝，在一般情況下不會出現這種情況。
3. The vibrator is unglued. Our transducer adopts the double assurance process of cementation and screw fastening, which generally does not occur.
4 不銹鋼振動面穿孔，一般換能器滿負荷使用10年以后可能會出現振動面穿孔的情況。
4. The vibration surface of stainless steel is perforated. Generally, after 10 years of full load use, the vibration surface may be perforated.