一、注意選擇適合的頻率
1、 Pay attention to selecting the appropriate frequency
操作簡便的超聲波清洗設備廠家介紹其頻率從十幾kHz到上百kHz之間，由空穴作用引起的物理清洗力顯然對低頻有利，一般使用比較小的頻率就可以了，具體應該按照規定數值操作。同時超聲波清洗設備廠不規則零件的家庭提醒，如小間隙或深孔，要用高頻清洗更好，甚至數百kHz；例如，當清洗時鐘和手表時，使用400千赫。如果采用寬帶調頻清洗，效果更好。
The manufacturer of ultrasonic cleaning equipment with simple operation introduced that its frequency ranges from more than ten kHz to over a hundred kHz. The physical cleaning force caused by cavitation is obviously beneficial for low frequencies. Generally, a relatively small frequency is sufficient, and specific operations should be carried out according to the specified values. At the same time, ultrasonic cleaning equipment factories remind families of irregular parts, such as small gaps or deep holes, to use high-frequency cleaning is better, even hundreds of kHz; For example, when cleaning clocks and watches, use 400 kHz. If broadbａnd frequency modulation cleaning is used, the effect is better.
二、注意選擇適當?shù)那逑匆簻囟?br>2、 Pay attention to selecting an appropriate cleaning fluid temperature
超聲波清洗設備制造商介紹，水清洗液適宜的清洗溫度是幾十度，特別是在寒冷的天氣。度低空化效應差，清洗效果也差。因此超聲波清洗設備廠家發現有部分清洗機在清洗缸外邊繞上加熱電熱絲進行溫度控制，當溫度升高后空化易發生，所以清洗效果較好。當溫度繼續升高以后，空泡內氣體壓力增加，引起沖擊聲壓下降，反應出這兩因素的相乘作用。

According to the manufacturer of ultrasonic cleaning equipment, the suitable cleaning temperature for water cleaning liquid is tens of degrees, especially in cold weather. The cavitation effect is poor at low temperature, and the cleaning effect is also poor. Therefore, manufacturers of ultrasonic cleaning equipment have found that some cleaning machines wrap heating wires around the outside of the cleaning cylinder for temperature control. When the temperature rises, cavitation is prone to occur, so the cleaning effect is good. When the temperature continues to rise, the pressure of the gas in the bubble increases, causing a decrease in the impact sound pressure, reflecting the multiplication of these two factors.
三。應注意清洗液量的測定和清洗部件的位置。
III. Attention should be paid to the measurement of the amount of cleaning fluid and the location of cleaning components.
服務質量高的超聲波清洗設備廠家介紹一般清洗液液面高于振動子表面要有十厘米的距離，效果比較好，如果量太少了，可能確實不干凈，如果量太多了，可能清水沖洗會帶來困難。由于單頻清洗機受駐波場的影響，波節處振幅很小，波幅處振幅大造成清洗不均勻，因此超聲波清洗設備廠家提醒選擇清洗物品的位置應放在波幅上。以上就是超聲波清洗設備在使用時需要注意的幾個事項，另外對于特殊的情況，還需要注意按照規范來操作機器，比如應該要先倒入清洗液，然后再開機，否則可能會對器件有所損壞。超聲波清洗設備制造商
The manufacturer of ultrasonic cleaning equipment with high service quality recommends that generally, the liquid level of the cleaning fluid should be ten centimeters above the surface of the vibrator, which has a relatively good effect. If the amount is too small, it may indeed not be clean. If the amount is too large, it may cause difficulties for washing with clean water. Due to the influence of the standing wave field on a single frequency cleaning machine, the amplitude at the wave node is very small, and the amplitude at the wave amplitude is large, resulting in uneven cleaning. Therefore, the manufacturer of ultrasonic cleaning equipment reminds that the location of cleaning items should be placed on the wave amplitude. The above are some precautions to be taken when using ultrasonic cleaning equipment. In addition, for special situations, it is also necessary to operate the machine in accordance with specifications. For example, it should be poured in cleaning liquid before starting up, otherwise the device may be damaged. Manufacturer of ultrasonic cleaning equipment
還應提醒，如果所使用的清洗液是易燃的，則應在盡可能短的時間內進行工作并加以保護。旁以保證安全問題。
It should also be reminded that if the cleaning fluid used is flammable, it should be worked and protected in the shortest possible time. To ensure safety issues.